Nursing Elites

1. In the mechanical power equation P = E / t, power is measured in ___________.

• A. ohms
• B. Joules
• C. volts
• D. watts

Correct answer: D

Rationale: In the mechanical power equation P = E / t, power is measured in watts. Watts are the standard unit of power in the International System of Units (SI), named after the Scottish engineer James Watt. Watts are defined as joules per second, reflecting the rate at which energy is transferred or converted. Ohms (choice A) are the unit of electrical resistance, Joules (choice B) are the unit of energy, and volts (choice C) are the unit of electric potential difference. Therefore, the correct answer is watts as it directly relates to power in the given equation.

2. What characterizes laminar flow?

• A. Smooth, parallel layers of fluid particles
• B. Erratic and turbulent motion of fluid particles
• C. High viscosity hindering flow
• D. Incompressibility of the fluid

Correct answer: A

Rationale: Laminar flow is characterized by the smooth, parallel movement of fluid particles along layers in a predictable manner. This flow regime occurs at low velocities and is in contrast to turbulent flow, where fluid particles exhibit erratic and chaotic motion. The viscosity of the fluid does not hinder laminar flow; instead, it influences the resistance to flow. Incompressibility is a property of fluids but does not specifically define laminar flow. Therefore, the correct answer is A as it accurately describes the behavior of fluid particles in laminar flow, making B, C, and D incorrect.

3. Which of the following is NOT a mode of heat transfer between a system and its surroundings?

• A. Conduction
• B. Convection
• C. Radiation
• D. Isothermalization

Correct answer: A

Rationale: Isothermalization is not a mode of heat transfer. The three main modes of heat transfer are conduction (through direct contact), convection (through fluid motion), and radiation (through electromagnetic waves). In this question, choice A, conduction, is not a mode of heat transfer between a system and its surroundings. Conduction refers to heat transfer through direct contact between particles, without the movement of the particles themselves. Therefore, A is the correct answer. Choices B, C, and D are incorrect as they represent valid modes of heat transfer.

4. A key parameter in fluid selection is specific gravity (SG). For a submerged object in a reference fluid (often water), SG = ρ_object / ρ_reference. An object with SG > 1 will:

• A. Experience a net buoyant force acting upwards
• B. Experience a net buoyant force acting downwards
• C. Remain neutrally buoyant
• D. Require knowledge of the object's volume for buoyancy determination

Correct answer: A

Rationale: When the specific gravity (SG) of an object is greater than 1, it indicates that the object is denser than the reference fluid, which is often water. According to Archimedes' principle, an object with SG > 1 will experience a net buoyant force acting upwards when submerged in the fluid. This is because the buoyant force is greater than the weight of the object, causing it to float. Therefore, the correct answer is A: 'Experience a net buoyant force acting upwards.' Objects with SG < 1 would sink as they are less dense than the fluid, while objects with SG = 1 would be neutrally buoyant, neither sinking nor floating.

5. The triple point of a substance is the specific temperature and pressure at which all three phases (solid, liquid, and gas) can coexist in thermodynamic equilibrium. Which of the following statements about the triple point is true?

• A. It can vary depending on the container size.
• B. It is a unique point for each pure substance.
• C. The pressure at the triple point can be zero for some substances.
• D. The temperature at the triple point can be above the boiling point of the liquid phase.

Correct answer: B

Rationale: The triple point is a unique temperature and pressure where all three phases (solid, liquid, and gas) of a pure substance can coexist in equilibrium. It is a constant for each substance and independent of container size. Choice A is incorrect because the triple point is a fixed point regardless of the container size. Choice C is incorrect as the pressure at the triple point is specific for each substance and will not be zero unless the substance has unique properties. Choice D is incorrect since the temperature at the triple point is precisely defined and cannot be above the boiling point of the liquid phase.

Similar Questions