Nursing Elites

1. Add: 1.332 + 0.067

• A. 1.399
• B. 1.4
• C. 1.402
• D. 1.5

Correct answer: A

Rationale: To find the sum of 1.332 and 0.067, add the two numbers correctly: 1.332 + 0.067 = 1.399. Therefore, the correct answer is A. Choice B (1.4) is incorrect because it rounds down the sum, not considering the precise value. Choice C (1.402) is incorrect as it results from adding 1.332 and 0.070 instead of 0.067. Choice D (1.5) is not the correct sum of the given numbers.

2. For his daily commute, Paul drives about 115 miles round trip. If he fills up his gas tank with 9 gallons every other day, about how many miles per gallon is his car averaging?

• A. 12.8
• B. 23
• C. 25.6
• D. 57.5

Correct answer: C

Rationale: To find the miles per gallon Paul's car is averaging, we first need to determine the miles he drives on 9 gallons of gas. Since he drives about 115 miles round trip daily, he covers approximately 115/2 = 57.5 miles one way. If he fills up his gas tank with 9 gallons every other day, he covers 115 miles every 2 days. This means his car is averaging around 57.5 miles per 9 gallons, which equals approximately 6.38 miles per gallon. As he uses 9 gallons every other day, his car averages about 6.38 * 2 = 12.76 miles per gallon. Among the given options, the closest value to this calculation is option C, 25.6 miles per gallon. Choice A is incorrect because it does not accurately reflect the mileage per gallon calculation. Choice B is incorrect as it is not the closest to the calculated value. Choice D is incorrect as it is significantly higher than the calculated mileage per gallon.

3. In a table showing blood pressure readings for different age groups, how do you determine the patient with the highest systolic pressure?

• A. Find the largest number in the 'systolic pressure' column.
• B. Compare the means (averages) of each age group.
• C. Add all systolic pressure values and divide by the total number of patients.
• D. Subtract the lowest systolic pressure from the highest.

Correct answer: A

Rationale: To determine the patient with the highest systolic pressure from the table, you should find the largest number in the 'systolic pressure' column. This method directly identifies the individual with the highest systolic pressure. Comparing the means (averages) of each age group, as suggested in choice B, may not pinpoint the specific patient with the highest systolic pressure, as averages can sometimes mask extreme values. Adding all systolic pressure values and dividing by the total number of patients, as in choice C, calculates the average systolic pressure for all patients, not identifying the highest individual reading. Subtracting the lowest systolic pressure from the highest, as in choice D, determines the range of systolic pressures but does not directly point out the patient with the highest reading.

4. Richard wants to make 2.5 batches of sugar cookies. One batch calls for 1.75 cups of sugar. How many cups of sugar will Richard need for 2.5 batches?

• A. 4
• B. 3
• C. 5 cups
• D. 3

Correct answer: A

Rationale: To calculate how much sugar Richard needs for 2.5 batches, multiply the amount of sugar needed for one batch (1.75 cups) by 2.5: 1.75 × 2.5 = 4.375  cups 1.75×2.5=4.375 cups Since the question is asking for the nearest whole number, 4.375 rounds to 4.

5. An IV bag contains 500ml of saline solution and needs to be infused over 4 hours. What is the flow rate in drops per minute, assuming 20 drops per milliliter?

• A. 12.5 drops/min
• B. 25 drops/min
• C. 50 drops/min
• D. 100 drops/min

Correct answer: C

Rationale: To find the flow rate in drops per minute, first, calculate the total volume in drops by multiplying the volume in milliliters by the number of drops per milliliter (500ml * 20 drops/ml = 10,000 drops). Then, divide this total number of drops by the infusion time in minutes (4 hours * 60 minutes/hour = 240 minutes) to get the flow rate. Therefore, the correct flow rate is 50 drops/min. Choice A is incorrect because it miscalculates the flow rate. Choice B is incorrect as it also miscalculates the flow rate. Choice D is incorrect as it overestimates the flow rate.

Similar Questions