Nursing Elites

1. A 3-volt flashlight uses a bulb with 60-ohm resistance. What current flows through the flashlight?

• A. o.05 amp
• B. o.5 amp
• C. 1.8 amp
• D. 18 amp

Correct answer: A

Rationale: : Using Ohm's Law, I = V / R: I = 3 / 60 = 0.05 amp. So, the correct current is 0.05 amp.

2. At which point on a roller coaster does the car have the greatest potential energy?

• A. The start of the ride
• B. The highest peak
• C. The lowest trough
• D. The end of the ride

Correct answer: B

Rationale: The correct answer is B, the highest peak. At the highest peak of the roller coaster, the car reaches its maximum height above the ground. This point represents the car's greatest potential energy because it has the highest potential to do work due to its elevated position. The potential energy is directly proportional to the height of an object, so the highest point on the roller coaster track corresponds to the car's greatest potential energy. Choices A, C, and D are incorrect because potential energy is highest at the peak due to its elevated position, not at the start of the ride, the lowest trough, or the end of the ride.

3. Which conclusion can be drawn from Ohm’s law?

• A. Voltage and current are inversely proportional when resistance is constant.
• B. The ratio of the potential difference between the ends of a conductor to current is a constant, R.
• C. Voltage is the amount of charge that passes through a point per second.
• D. Power (P) can be calculated by multiplying current (I) by voltage (V).

Correct answer: B

Rationale: Ohm's law states that the ratio of the potential difference (voltage) between the ends of a conductor to the current flowing through it is a constant. Mathematically, this is represented as V = I x R, where V is voltage, I is current, and R is the constant resistance. Therefore, the correct conclusion that can be drawn from Ohm's law is that the ratio of the potential difference between the ends of a conductor to current is a constant, denoted as R. This relationship is fundamental to understanding the behavior of electrical circuits and the effect of resistance on voltage and current. Choice A is incorrect because Ohm's law actually states that voltage and current are directly proportional when resistance is constant. Choice C is incorrect because voltage is not the amount of charge that passes through a point per second; rather, it is the electric potential energy per unit charge. Choice D is incorrect because although power (P) can be calculated by multiplying current (I) by voltage (V), this is not a conclusion directly drawn from Ohm's law.

4. Which of the following is NOT a mode of heat transfer between a system and its surroundings?

• A. Conduction
• B. Convection
• C. Radiation
• D. Isothermalization

Correct answer: A

Rationale: Isothermalization is not a mode of heat transfer. The three main modes of heat transfer are conduction (through direct contact), convection (through fluid motion), and radiation (through electromagnetic waves). In this question, choice A, conduction, is not a mode of heat transfer between a system and its surroundings. Conduction refers to heat transfer through direct contact between particles, without the movement of the particles themselves. Therefore, A is the correct answer. Choices B, C, and D are incorrect as they represent valid modes of heat transfer.

5. The Reynolds number (Re) is a dimensionless quantity used to characterize:

• A. Fluid density
• B. Flow regime (laminar vs. turbulent)
• C. Surface tension effects
• D. Buoyancy force magnitude

Correct answer: B

Rationale: The Reynolds number is a dimensionless quantity used to characterize the flow regime, specifically whether it is laminar (smooth) or turbulent (chaotic). It depends on the velocity of the fluid, its characteristic length (such as pipe diameter), and its viscosity. A low Reynolds number indicates laminar flow, while a high Reynolds number suggests turbulence. Choices A, C, and D are incorrect because the Reynolds number is not related to fluid density, surface tension effects, or buoyancy force magnitude.

Similar Questions